Difference between revisions of "Configuring for GPS Location and Time Synchronization"

Latest revision as of 05:11, 9 October 2014

Network Time Protocol (NTP)

NTP is a time synchronizing protcol.It synchronizes the time of the machines on a network by using the set of time servers as its reference.

Need for time synchronization

Most of us believe that the computer clocks are accurate,being unaware of the fact that the crystal oscillator that is being used in the computer clocks drift each day because it is sensitive to temperature and other things.It is because of this reason there is a necessity for those organizations to synchronize their computers clocks who requires time accuracy nearest to seconds.

Importance of Time Synchronization

In today's era time synchronization plays a critical role in managing or debugging things over the network as each event requires time stamp.Following are the areas where time synchronization is critical:

1. Transaction Management
2. Billing Services
3. Detecting the fault over network

Basic Features of NTP

1. NTP also requires some time reference clock with whose time it can synchronize the clocks of other computers on the netwrok.It uses UTC as reference time.
2. NTP selects the best among all defined time servers to get synchronize to.It selects the one from which it is receiving the reply in lesser time(i.e. for whom the roundtrip time is least )
3. If the network is temporarily not available then NTP uses previous measurements to get the current time.

Installing and Configuring NTP for GPS NMEA and PPS

To get accurate time, we use the GPS Module Navika100 GPS NMEA messages and 1 PPS signal as inputs and feed it to a NTP server running on the Beaglebone black.

This page describes how it is done. The overall architecture is like this: NTP runs as a daemon (ntpd). It receives inputs from servers (pool.ntp.org, etc.), and NMEA drivers.

Installing NTP and setting up a NTP server

Note:All commands are executed as root on Beaglebone Black unless mentioned otherwise.

Basic initial configuration:

• BBB should be connected to internet
• BBB should be running debian wheezy
• kernel should have the pps support

Before configuring GPS with NTP first install the ntp package :

login as root using

 
$ sudo su

install ntp

$ apt-get install ntp

Change the configuration file of ntp on Beaglebone Black to include the servers according to your time zone to obtain the time.

$ nano /etc/ntp.conf

Add the ntp server as per your location from NTP Pool Servers.

If your time zone is Asia and in Asia you are in India then add the following in ntp.conf just after the section where 4 servers from debian are already mentioned and by default commented. Uncomment the first server from that list, to look like this :

 
server 0.debian.pool.ntp.org
#server 1.debian.pool.ntp.org iburst
#server 2.debian.pool.ntp.org iburst
#server 3.debian.pool.ntp.org iburst

server 0.in.pool.ntp.org
server 3.asia.pool.ntp.org
server 0.asia.pool.ntp.org

Now Save and exit.

Restart ntp using

$ /etc/init.d/ntp restart

To check the ntp output:

$ ntpq -p

Configuring GPS NMEA UART port and PPS GPIO to work with Navika 10 GPS Module

Go to the following directory for enabling UART port and configuring PPS GPIO

cd /lib/firmware

Now ensure that the BBB Vayu overlay is already present in the directory (BBB_VAYU-00A0.dtbo)

ls

If it is not present, please download and copy the overlay from here

Apply the following device tree overlays :

$ echo BB-UART4 > /sys/devices/bone_capemgr.9/slots
$ echo BBB_VAYU > /sys/devices/bone_capemgr.9/slots

To check that the overlays have been properly applied , do following :

i. Check slots for device trees implemented

$ cat /sys/devices/bone_capemgr.9/slots

The output should be like this :

0: 54:PF--- 
1: 55:PF--- 
2: 56:PF--- 
3: 57:PF--- 
4: ff:P-O-L Bone-LT-eMMC-2G,00A0,Texas Instrument,BB-BONE-EMMC-2G 
5: ff:P-O-L Bone-Black-HDMI,00A0,Texas Instrument,BB-BONELT-HDMI 
7: ff:P-O-L Override Board Name,00A0,Override Manuf, BB-UART4
8: ff:P-O-L Override Board Name,00A0,Override Manuf, BBB_VAYU

L indicates that the device tree overlay is applied.

ii To check that PPS GPIO has been configured, check the system log messages and list of devices :

 
$ dmesg

It should show pps pps1: Registered IRQ 171 as PPS source in the messages.

Now, to read the GPS NMEA packets and see their raw format,do the following :

Note1:Ensure that GPS Antenna has been connected to correct antenna SMA connector.

Note2:GPS Fix Led takes some time before it starts blinking in sync with 1 pps signal.

Note3:For better and faster results, keep GPS antenna under open sky or outdoors. Indoors, GPS antenna may take time to get the sync as well as give accurate NMEA messages.

Set the following port settings for UART4 to read the GPS NMEA messages

$ stty -F /dev/ttyO4 19200 raw

Read the data on the port and output should be something like :

$ cat /dev/ttyO4

$GPGSA,A,3,02,04,12,25,24,05,10,,,,,,02.4,01.1,02.1*07 
$GPGLL,2834.2631,N,07720.5426,E,102954.00,A,A*6E 
$GPGSV,3,1,07,02,71,345,50,04,40,038,48,12,62,315,47,25,20,321,45*7F 
$GPGSV,3,2,07,05,41,167,23,10,48,086,23,24,24,236,30,,,,*48 
$GPGSV,3,3,07,,,,,,,,,,,,,,,,*7E 

Using Xgps and Gpsd to work with Navika

Using Gpsd

Gpsd allows a direct connection to a GPS receiver, in this case the Navika module, and collecting NMEA messages directly from the serial port. This enables NMEA messages to be then picked up by multiple clients such as xgps, cgps and also ntpd.

• Check first that Navika is configured correctly and gps data is reaching the /dev/ttyO4 port.

cat /dev/ttyO4

You should see NMEA messages appearing on stdout.

• Starting GPSD can be done interactively by

gpsd /dev/ttyO4 -D 8 -N -b

Or you may set it up as a service as well to start automatically. Once gpsd starts, clients may connect to gpsd simultaneously.

For enabling NMEA messages in NTP, add the following to /etc/ntp.conf:

server 127.127.28.0 minpoll 4 maxpoll 4
fudge 127.127.28.0 time1 0.420 refid GPS 

server 127.127.28.1 minpoll 4 maxpoll 4 prefer
fudge 127.127.28.1 refid GPS1

and then restart ntpd.

To run and see xgps, type

xgps

A screenshot is shown below:

To run and use cgps, type

cgps

A screenshot is shown below:

Statistics collection

If statistics collection is enabled in /etc/ntp.conf file, you can see the resultant output logged in peerstats file. This gives both offset and jitter values for each reference clock (including time servers from the ntp.org pool). By looking specifically at the NMEA reference clock, we can get the gps jitter and gps offset values. Separately, it is also possible to compare the effect of pps on the basic gps signal (see Getting PPS and GPS to work with NTP server for details).

Getting PPS and GPS to work with NTP server

This procedure requires Kernel with PPS drivers enabled and also PPS configured for GPIO. To ensure that PPS drivers are there in the kernel by following the steps:

1. login as root (ignore if you are already at root)
2. check in the /dev directory whether pps drivers are there or not

    $ ls /dev/pps*

you should see pps0 in the list

Note: If pps0 is not present, please follow Add USB and PPS drivers to update the kernel to include PPS drivers.

Install the following packages

    $ apt-get install ncurses-dev
    $ apt-get install bzip2
    $ apt-get install module-init-tools
    $ apt-get install initramfs-tools
    $ apt-get install procps 
    $ apt-get install fakeroot
    $ apt-get install zlib1g-dev 
    $ apt-get install git-core 
    $ apt-get install libblkid-dev
    $ apt-get install kernel-package 

Note: In latest kernel versions, it is possible few packages mentioned above are already installed.

Obtain the linuxpps userland tools

    $ cd /usr/src
    $ git clone git://www.linuxpps.org/git/pps-tools pps-tools

Copy the timepps.h file so ntpd gets built with pps support

    $ cd /usr/include
    $ cp /usr/src/pps-tools/timepps.h timepps.h

Build the ppstest tool

    $ cd /usr/src/pps-tools
    $ make 

Obtain and build ldattach

    $ cd /usr/src
    $ mkdir ldattach 
    $ cd ldattach
    $ wget http://www.kernel.org/pub/linux/utils/util-linux-ng/v2.14/util-linux-ng-2.14.2.tar.bz2
    $ tar jxf util-linux-ng-2.14.2.tar.bz2
    $ cd util-linux-ng-2.14.2
    $ ./configure
    $ make

Note : If the link http://www.kernel.org/pub/linux/utils/util-linux-ng/v2.14/util-linux-ng-2.14.2.tar.bz2 doesn't work,then try using the link http://www.artfiles.org/kernel.org/pub/linux/utils/util-linux-ng/v2.14/util-linux-ng-2.14.2.tar.bz2. If util-linux is unavailable from both locations, please download the same from here util-linux-ng-2.14.2.tar.bz2.

Copy ldattach

    $ cd sys-utils
    $ cp ldattach /usr/sbin/

Create pps port

$ ldattach pps /dev/pps1

Note: Ignore any errors here

Test PPS (pps0 or pps1 )

    $ cd /usr/src/pps-tools/
    $ ./ppstest /dev/pps1

The output should be something like this :

    trying PPS source "/dev/pps1"
    found PPS source "/dev/pps1"
    ok, found 1 source(s),now start fetching data...
    source 0 -assert 1351501153.999956346, sequence: 4781 - clear 0.00000000, sequence: 0
    source 0 -assert 1351501154.999954601, sequence: 4782 - clear 0.00000000, sequence: 0
    source 0 -assert 1351501155.999951856, sequence: 4782 - clear 0.00000000, sequence: 0

Note : PPS support can be checked even without the specific hardware by using ktimer which is there in the kernel. It can be checked on /dev/pps0.Therefore,always check the pps data on /dev/pps1 which is coming from the Navika100 module because on /dev/pps0 the pps data would be there even if the Navika100 has not got the GPS fix.

Now having NTP daemon perform the following steps

    $ mkdir /usr/src/ntp     (Make a convenient working directory , if you don't already have one)
    $ cd ntp
    $ apt-get install libcap-dev
    $ wget http://www.eecis.udel.edu/~ntp/ntp_spool/ntp4/ntp-4.2/ntp-4.2.6p5.tar.gz
    $ tar xvfz ntp-4.2.6p5.tar.gz
    $ cd ntp-4.2.6p5
    $ ./configure 
    $ make 
    $ make install

NMEA reference clock driver directly accesses the serial port. Expects that the port will be numbered /dev/gpsX and /dev/gpsppsX, where X is 0,1,2... Corresponding to each X, it creates a pseudo-ip 127.127.20.X

So,make the soft links for ntpd to read gps nmea and 1 pps as input

    $ ln -s /dev/ttyO4 /dev/gps1
    $ ln -s /dev/pps1 /dev/gpspps1

Configure the ntp.conf file so that ntpd(ntp daemon) can read 1pps and gps data

    $ nano /etc/ntp.conf

Edit the file as :

1. Uncomment statsdir /var/log/ntpstats

2. Add the ntp server as per your location from NTP Pool Servers

Note: This step is already done in section 2, servers should already be present

3. Add support for GPS and PPS ( add them just after the list of servers)

        # NMEA refclock driver directly from serial port
        server 127.127.20.1 mode 47 minpoll 4 iburst prefer true
        fudge 127.127.20.1 flag1 1 flag2 0 flag3 0 flag4 0 time1 0.00 refid GPS
        # ATOM PPS driver directly from interrupt through /dev/pps1
        server 127.127.22.1 mode 47 minpoll 4 maxpoll 4 iburst true
        fudge 127.127.22.1 flag2 0 flag3 0 flag4 1 time1 0.0 refid PPS

Save and Exit

Note : The direct serial port driver 20.0 or 20.1 from NMEA are different from 127.127.28.1 the one mentioned above.

Now, edit the following file:

$ nano /etc/init.d/ntp

Edit PATH in the file to add /usr/local/bin to look like :

PATH=/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin

And change the path of DAEMON to following :

DAEMON=/usr/local/bin/ntpd

Save and Exit

Commands for NTP server

    $ service ntp start           
    $ service ntp stop            
    $ service ntp restart

To check whether ntpd is working with GPS NMEA and PPP or not :

    $ ntpq -p

The output should be something like :

     remote           refid      st t when poll reach   delay   offset  jitter
==============================================================================
-120-88-47-10.in 103.1.106.69     2 u   43   64  377   51.624  537.091   1.517
+27.114.150.13   130.133.1.10     2 u   36   64  377  222.386  481.023   0.583
+77.235.14.49    131.188.3.220    2 u   41   64  377  284.982  510.672   1.408
*GPS_NMEA(1)     .GPS.            0 l   10   16  377    0.000    1.996   0.204
oPPS(1)          .PPS.            0 l    9   16  377    0.000  -469.94   0.191

Note:

Showing the Jitter and Offset of 1PPS when NTP gets synchronized with it

1. If GPS_NMEA(1) and PPS(1) are not visible in the list of servers as shown above, just restart the NTP Server.
2. The '*' in front of GPS shows that the peer has been declared the system peer and lends its variables to the system variables.
3. The 'o' shows that the peer has been declared the system peer and lends its variables to the system variables. However,the actual system synchronization is derived from a pulse-per-second(PPS) signal,either indirectly via the PPS reference clock or directly via kernel interface.

As soon as the ntp gets synchronized with the pps the jitter in the time starts decreasing and becomes stable after some time.

Note on NTPd and its settings

NTPd is certainly not the only way to use the GPS and PPS inputs although it is indeed pretty good. Considering the number of knobs it has, one must understand its workings to get good results. The settings used in /etc/ntp.conf are crucial in deciding this and can take quite a lot of effort to set up properly. If you're using ntpd, it is better to use the ntp clock discipline instead of the kernel discipline. Also, choosing the right time server is important as the offset and jitter of the external time server clock take a long time to be mitigated locally. These points become clear if you carefully study the following figures for some long term data as ntpd slowly settles.

References

1. Ntp official website
2. GPSD Berlios site
3. Enabling ntpd pps support for debian
4. Synchronizing an NTP server for GPS/PPS
5. Description of Generic NMEA Receiver
6. Description of PPS clock Discipline